New Install

  • Anonymous May 21, 2012 at 4:53 pm

    Router NameDD-WRT

    Router ModelBuffalo WZR-HP-G300NH2

    Firmware Version

    DD-WRT v24SP2-MULTI (10/31/11) std – build 17798

    Operator Username

    Location ID

    DHCP Interface LAN

    Remote Network

    Special SettingsEnable Disable

    White Label Protocolhttp https

    White Label Domain

    Login on splash page

    Enable Disable

    I have already ran the command. And once enable the hotspotsystem from Buffalo>>Service>>hotspot. And it resets, I get connected to my original SSID but no interent connection is there..just get error message of page cannot load. Do I need to turn of my WPA secruity and SSID settings, or is there something else I am missing.All I want is for guests to logon and be prompted with splash page with terms and agreement accpetance. Nothing else for now, if it work then I can upgrade for payments.

    Thanks

    Anonymous May 21, 2012 at 4:55 pm

    username: hdpate

    location id : 1

    DHCP: LAN

    Remote network: 192.168.182.0/24>>>>>>>does this need to be changed?

    special settings: enable

    https

    login spalsh page: enable

    Anonymous May 22, 2012 at 1:31 pm

    The settings are fine. Connect to the router with telnet and see if chili is running, if not try to start it and let me know if you get an error: http://hotspotsystem.com/deskpro/kb_article.php?ref=7681-YOAN-6356

    If it is running, check to see what the ip address you get when connecting to the router?

    Anonymous May 22, 2012 at 4:38 pm

    ok. got to the point of asking DD-wrt login. Are these the login in settings for my router or hotspotsystem..i tried both and invalid login?!

    Anonymous May 22, 2012 at 4:54 pm

    the username is root when logging in via telnet

    Anonymous May 22, 2012 at 5:17 pm

    and password? btw i type telnet 192.168.11.1 to access dd-rt login..is that right? thanks

    Anonymous May 22, 2012 at 5:33 pm

    ok soo i was able to login but but i do not see the chilispot. i tried manually typing it but with no luck, when and where do I type the commmand

    Anonymous May 22, 2012 at 5:56 pm

    you can start chilli with

    chilli -c /tmp/hotss.conf

    or chilli -c /tmp/chilli.conf for olderbuilds.

    The router has to be connected to the internet for chilli to be able to start!

    Anonymous May 22, 2012 at 7:56 pm

    after logging into router it says segmentation fault?

    I tried typing both commands.

    Anonymous May 22, 2012 at 8:02 pm

    and router is connected to internet. I am doing this all wireless.

    Anonymous May 23, 2012 at 10:51 am

    Segmentation fault means that the build will not work due to a glitch. I suggest that you either try to flash the router with build 14311 or try to manually add the chillispot settings as per this article (reset the router to factory defaults first) http://hotspotsystem.com/deskpro/kb_article.php?ref=6681-USDK-3810

    Anonymous May 24, 2012 at 5:04 pm

    Still no go. I tried manually installing chillspot. I am able to connect to router but not internet. I get a yellow exclamation sign in my network settings. Is there a easier way to help from you, I feel this forum will take longer time and energy than you helpin live via chat or remotely?

    Anonymous May 25, 2012 at 1:21 pm

    A yellow sign does not necessarily mean the connection is not working. It normally will display a restricted connection message, or further login required. You should try a different build, use 14311 if you can find it for your router. We have to stay with this method to help you, as for Hotspot Basic account users we provide support through the forums.

    Anonymous May 29, 2012 at 7:40 pm

    How do I try a different build?

    Also if I upgrade my service, how quickly can we get this resolved. I will upgrade my account to get this resolved ASAP, can you remotely help me do this, or would the upgrade basically be this forum but via live chat?!

    Anonymous May 30, 2012 at 10:46 am

    If you upgrade you get live chat support and limited telephone/remote desktop support. To flash the router you need to login the admin and navigate to the administration/flash firmware and select the firmware you downloaded from DD-wrt.com. You can select a specific build with the “supported by” pull down menu. The procedure is the same as when you 1st flashed the router, except now you only need the standard generic image, as in the setup guide: http://hotspotsystem.com/en/hotspot/install_guide_dd-wrt.html

    You should reset the router's setting when upgrading.

0 0
1 2

You must be logged in to reply to this topic.